ремонт холодильников AEG в Москве и области от компании Град Сервис. Диагностика входит в стоимость ремонта
AEG service            +7(495)255-2253

AEG service

Коды ошибок и неисправностей AEG

5.5 TABLE OF ALARMS

Alarm Possible fault Action/machine status Reset Alarm Page

E00 No alarm ---------------- ---------------- ---------------- ----------

E11 Difficulties in water fill for washing
Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle is paused with door locked.
START/RESET 23

E12 Difficulties in water fill for drying
Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle is paused with door locked.
START/RESET 25

E13 Water leakage
Drain hose incorrectly positioned; mains pressure insufficient; water fill solenoid faulty; leakage/blockage of pressure switch hydraulic circuit; pressure switch faulty. Cycle is paused with door locked.
START/RESET 26

E21 Difficulties in draining for washing
Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle is paused (after 2 attempts).
START/RESET 28

E22 Difficulties in draining for drying
Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle is paused.
START/RESET 30

E23 Drain pump triac faulty
Drain pump faulty; Wiring faulty; PCB faulty. Safety drain cycle - Cycle stops with door unlocked.
RESET 32

E24 Fault in “sensing” circuit of drain
pump triac (wrong input signal to microprocessor) PCB faulty. Safety drain cycle - Cycle stops with door unlocked.
RESET 33

E31
Electronic pressure switch circuit faulty (frequency of pressure switch signal out of limits) Electronic pressure switch; Wiring; PCB faulty. Cycle blocked with door closed.
RESET 33

E32 Incorrect calibration of electronic pressure switch
(The electronic pressure switch generates a signal with instable frequency during the drain phase) Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Leaks from water circuit on pressure switch; Pressure switch; Wiring faulty; PCB faulty. Cycle is paused.
START/RESET 34

E35 Water overflow Water fill solenoid faulty;
Leaks from water circuit on pressure switch; pressure switch faulty; wiring faulty; PCB faulty. Cycle blocked. Safety drain cycle. Drain pump always in operation (5 minutes on, 5 minutes off etc.).
RESET 35

E38 Pressure chamber blocked
(water level does not vary for at least 30 sec. during drum rotation Motor drive belt broken; Hydraulic circuit pressure switch clogged. Heating phase skipped.
ON/OFF RESET 36

E3A Heating elem. relay sensing faulty
(input signal to microprocessor always 0V or 5V) PCB faulty. Cycle blocked with door closed.
RESET 37

E41 Door open (after 15 sec.)
Door interlock faulty; wiring faulty; PCB faulty. Cycle paused.
START/RESET 38.41

07-2010 SOI/DT-mdm FCPD-dp Quality-fz 18/95 599 70 56-70 Alarm Possible fault Action/machine status Reset Alarm Page

E42 Problems of door closure Door interlock faulty;
wiring faulty; PCB faulty. Cycle paused.
START/RESET 42.44

E43 Interlock power supply triac faulty Door interlock faulty;
wiring faulty; PCB faulty. (Safety drain cycle) Cycle blocked.
ON/OFF RESET 46.47

E44 Door interlock sensing circuit triac
faulty PCB faulty. (Safety drain cycle) Cycle blocked.
ON/OFF RESET 48

E45 Door interlock sensing circuit triac faulty
(wrong input signal to microprocessor) PCB faulty. (Safety drain cycle) Cycle blocked.
ON/OFF RESET 48

E51 Motor power supply triac shortcircuited
PCB faulty; current leakage from motor or from wiring. Cycle blocked, door locked (after 5 attempts).
RESET 49

E52 No signal from motor tachometric
generator Motor faulty; wiring faulty; PCB faulty. Cycle blocked, door locked (after 5 attempts).
RESET 50.53

E53 Motor triac sensing circuit faulty
(input signal to microprocessor wrong) PCB faulty. Cycle blocked, door locked.
RESET 54

E54 Motor relay contacts sticking (high voltage level when the relay changes to OFF) PCB faulty; current leakage from motor or from wiring. Cycle blocked, door locked (after 5 attempts).
RESET 55

E61 Insufficient heating during washing NTC sensor faulty;
heating element faulty; wiring faulty; PCB faulty. The heating phase is skipped.
START/RESET 56

E62 Overheating during washing
(temperature higher than 88°C for a time higher than 5 min.) NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. Safety drain cycle – Cycle stopped with door open.
RESET 57.58

E66 Heating element power relay faulty
(incongruence between sensing and relay) PCB faulty. Safety drain cycle – Cycle stopped with door open.
RESET 59.60

E68 Current dispersion to earth
(value of mains voltage different from main value) Current dispersion between between heating element and earth. Cycle blocked with door open.
RESET 61.62

E69 Heating element interrupted Wiring faulty;
Heating element for washing interrupted (thermofuse open). Main circuit board faulty.
START/RESET 63.64

E71 Washing NTC sensor faulty
(shortcircuited or open) Wiring faulty; Washing NTC sensor faulty; PCB faulty. The heating phase is skipped.
START/RESET 65

E72 Drying condenser NTC sensor faulty
(voltage value out of limits, sensor short-circuited or open) Wiring faulty; Drying NTC sensor (condenser) badly positioned or faulty; WD board faulty. The drying heating phase is skipped.
START/RESET 66

E73 Drying duct NTC sensor faulty
(voltage value out of limits, sensor short-circuited or open) Wiring faulty; Drying NTC sensor (duct) badly positioned or faulty; WD board faulty. The drying heating phase is skipped.
START/RESET 67

E74 Washing NTC sensor badly
positioned Wiring faulty; Washing NTC sensor badly positioned; NTC sensor faulty; PCB faulty. The heating phase is skipped.
START/RESET 68

E82 Error in selector reset position PCB faulty
(Wrong configuration data).
RESET 69

E83 Error in selector reading PCB faulty (Wrong configuration data. Cycle cancelled.
START/RESET 70

07-2010 SOI/DT-mdm FCPD-dp Quality-fz 19/95 599 70 56-70 Alarm Possible fault Action/machine status Reset Alarm Page

E91 Communication error between PCB
and display board Wiring faulty; Control/display board faulty: PCB faulty.
RESET 71

E92 Communication incongruence
between main PCB- display board (versions not compatible) Wrong control/display board; Wrong PCB (do not correspond to the model). Cycle interrupted.
OFF/ON 71

E93 Incorrect configuration of appliance PCB faulty;
(Incorrect configuration data). Cycle interrupted.
OFF/ON 71

E94 Incorrect configuration of washing
cycle PCB faulty; (Incorrect configuration data). Cycle interrupted.
OFF/ON 71

E95 Communication error between
microprocessor and EEPROM PCB faulty. Cycle interrupted.
RESET 71

E97 Incongruence between programme
selector and cycle configuration Faulty PCB (Wrong configuration data). Cycle interrupted.
RESET 71

EA1 Drum positioning (DSP) faulty Motor belt broken;
Wiring faulty; PCB faulty; DSP sensor faulty. Positioning phase skipped.
ON/OFF RESET 72

EA6 DSP door opening faulty Motor belt broken;
Wiring faulty; Drum cover open. Motor faulty; PCB faulty. Cycle paused.
ON/OFF RESET 73

EH1 Frequency power of appliance out of limits Power supply problems (incorrect / disturbance);
PCB faulty. Wait for frequency nominal conditions.
OFF/ON 74

EH2 Voltage too high Power supply problems (incorrect / disturbance);
PCB faulty. Wait for frequency nominal conditions.
OFF/ON 74

EH3 Voltage too low Power supply problems (incorrect / disturbance);
PCB faulty. Wait for frequency nominal conditions.
OFF/ON 74

EF1 Drain filter blocked
(drain phase too long) Drain tube blocked/kinked/too high; Drain filter dirty/blocked. Warning displayed at the end of cycle (specific LED).
START/RESET 75

EF2 Excessive detergent dosing
(excessive foam during draining) Excessive detergent dosing; drain tube kinked/blocked; Drain filter dirty/blocked. Warning displayed after 5 attempts or by the specific LED.
RESET 75

EF3 Aqua control intervention Water leaks onto base frame;
water control system defective. Water drain.
ON/OFF RESET 75

EF4 Water fill pressure low, no signal of flowmeter and solenoid valve open Tap closed;
water fill pressure low.
RESET 75

EF5 Unbalanced load Final spin phases skipped.
RESET 75

EF6 Reset
No action to be performed, if continues replace the PCB.
75

EC1 Solenoid valve blocked with flowmeter working Wiring faulty;
Solenoid valve faulty/blocked, PCB faulty. Cycle blocked with door closed. Drain pump always works (5 min., then it stops for 5 min. ecc.).
RESET 76

Ed1 Data communication error between
WD board and PCB Wiring faulty between PCB and WD board; WD board faulty; PCB faulty. Cycle interrupted.
OFF/ON 77

Ed2 Drying heating element relay 1 faulty Wiring faulty between WD board and thermostats;
thermostats faulty; WD board faulty, PCB faulty. Cycle blocked with door open.
RESET 78

Ed3 Drying heating element relay 2 faulty Wiring faulty between WD board and thermostats;
thermostats faulty; WD board faulty, PCB faulty. Cycle blocked with door open.
RESET 81

07-2010 SOI/DT-mdm FCPD-dp Quality-fz 20/95 599 70 56-70 Alarm Possible fault Action/machine status Reset Alarm Page

Ed4 Relay which commutates power
between washing heating element and drying (in the WD board) Wiring faulty; WD board faulty; PCB faulty. Cycle blocked with door open.
RESET 82

Ed6 No communication between PCB
and display board (INPUT) Wiring faulty between PCB and programme display board; PCB faulty.
OFF/ON 84

           Вызвать мастера Сервисные центры Запчасти AEG Утилизация AEG Ошибки AEG Найти сервисный номер AEG
Прейскурант
Гарантия Книга жалоб Корпоративным клиентам Требуются мастера Контакты

Ремонт холодильников AEG